Accessories

Digital Thermometor to be used with Fibaro sensors.

• Temperature sensor to be used with Fibaro Door/Window Sensor and Universal Sensor
• Temperature range: -10°C to +85°C

Fibaro Temperature Sensor is an external, wireless temperature sensor for Radiator Thermostat.

• Wireless temperature sensor
• To be used with Fibaro Radiator Thermostat (sold separately)
• It can serve as a point of reference for up to three thermostatic heads at once
• Easy installation - no tools required

Change the look of your Eurotronic's Spirit Smart Radiator Thermostat with these design panels available in three stylish colours.

• Pack of 3 design panels for the Eurotronic Spirit thermostat
• Available in three different stylish colours
• Easy installation

MCO Home External Sensor for MCOEMH7H-EH

• To be used with the Z-Wave MCO Home Electrical Heating Thermostat with Humidity Sensor
• Overheat protection of the thermostats
• NTC R25℃=15KΩ B25℃/50℃=3550K
• Length: 3m

Digital Thermometor to be used with Fibaro sensors

• Temperature sensor to be used with Fibaro Door/Window Sensor and Universal Sensor
• Temperature range: -10°C to +85°C
• Pre-wired and waterproof

Digital temperature sensor to be used with Qubino modules.

• Digital temperature sensor
• 1m cable
• Digital temperature sensor range is between -50°C and 125°C.

External temperature probe for use with Secure Wall Switch

• Easy fit for new and replacement installations
• Used for pipe and hot water tank temperature sensing
• Temperature sensing for underfloor heating

Z-Wave Secure Pipe Tank Digital Temperature Sensor - 1m Wire

• Measure surface temperature of hot water flow pipes and hot water tanks
• Thermal pad for superior conductivity
• Digital temp IC for improved accuracy
• Can only be used with SES 302 or SES 303 temperature and humidity sensors
• Easy cascading using RJ10-RJ10 cascade cable (applicable for SES002)
• Up to four external digital temperature sensors are supported by cascading
• Supplied with a 1-metre long communication cable and 1-meter long cascading cable

Z-Wave Secure Pipe Tank Digital Temperature Sensor - 4m Wire

• Measure surface temperature of hot water flow pipes and hot water tanks
• Thermal pad for superior conductivity
• Digital temp IC for improved accuracy
• Can only be used with SES 302 or SES 303 temperature and humidity sensors
• Easy cascading using RJ10-RJ10 cascade cable (applicable for SES002)
• Up to four external digital temperature sensors are supported by cascading
• Supplied with a 4 meters long communication cable

Z-Wave Qubino Flush Module Pilot Wire ZMNHJD1 Plus with 3 digital inputs allow you to connect additional devices such as sensors, push buttons, or bistable

• Integrated Z-Wave chip series 500 (Z-Wave +)
• 250% faster communication compared to standard Z-Wave devices
• Very low power consumption of 0.4W with less
• Z-Wave Plus Certified

Wall casing to be used with the Qubino digital temperature sensor.

• Plastic wall mounting case
• Houses Qubino Temperature Sensor
• Dimensions: 71mm x 71mm x 27mm

Cable for Heatit Thermostat Software Updates

• For use with Z-Wave Heatit Thermostat
• Updates Heatit thermostats' software and firmware

Z-Wave Popp Flow Stop Gas/Water Shut-off Controller - Gen5 - Valuable helper in need

• Motor operated shut-off controller
• Automatic flow stop for gas and water pipelines
• Motor requires only 12V (1A)
• Closes the ball valve in just 10 seconds
• Controllable by PC, notebook, mobile devices - and sensors
• Quick and easy installation
• Z-Wave Plus Certified

Wall Mount Kit and charger for evohome controller.

• Allows your evohome controller to be mounted on the wall
• Includes mains charger to charge controller battery
• To be used with the new (v3) evohome controller

Opentherm bridge for evohome multi-zone heating.

• Allows the evohome heating system to control an Opentherm boiler
• Must be used with the evohome controller

Comap valve adapter for Danfoss Living Connect Thermostat

• For mounting a Danfoss Living Connect Thermostat instead of Comap valve
• Easy Installation

Herz valve adapter for Danfoss Living Connect Thermostat

• For mounting a Danfoss Living Connect Thermostat instead of Herz valve
• Easy Installation

MMA or S&B valve adapter for Danfoss Living Connect Thermostat

• For mounting a Danfoss Living Connect Thermostat instead of MMA or S&B valve
• Easy Installation

RAV and RAVL adapters for Danfoss Living Connect Thermostat

• For mounting a Danfoss Living Connect Thermostat instead of RAV or RAVl valve
• Adapters and press glands included
• Easy Installation

Honeywell Adapter ACH28

• Replacement valve baseplate for the Honeywell evohome HR92 Radiator Controller
• Allows Thermostatic Radiator Valves with a M28 x 1.5mm thread to fit with the HR92 Radiator Controller