Question 1

Will this work with lights and smart plugs connected via a Hue gateway? More specifically, I am using Home Assistant with a Hue gateway controlling a mix of Ikea Tradfri and other brands of bulbs/smart plugs. I am looking for a wall-mounted controller that Home Assistant can see and that ideally can control lights directly in case the hub loses connectivity. View answer

Asked 3 ´years ago | Vesternet Zigbee Wall Controller - 8 Button

Question 2

Is there is voltage leakage with 3 wire setup or is it only present in 2 wire setup? View answer

Asked 3 ´years ago | Vesternet Z-Wave Dimmer

Question 3

Does this work with Home Assistant? View answer

Asked 3 ´years ago | Vesternet Zigbee Dimmer

Question 4

Can this MCO MH7H-EH V2 thermostat be used to control both Electric Under Floor heating and a Towel warmer, but both independantly from each other please?If not, is there an alternative product which can do this ?Many thanks,Richard BlatchBoxford Suffolk View answer

Asked 3 ´years ago | Z-Wave Plus MCO Home Electrical Heating Thermostat with Humidity Sensor - V2

Question 5

Are these interlinked via radio frequency (separately to the zwave) to make them suitable for use in Scotland under the new regulations starting February 2022? View answer

Asked 3 ´years ago | Z-Wave Plus Popp Smoke Sensor with controllable Siren (2-in-1)

Question 6

Is there a button on the plug-switch to enable me to over-ride the light etc on/off please? View answer

Asked 3 ´years ago | Z-Wave Plus Secure Smart Plug Switch

Question 7

Are the contacts in this model 'dry'? I want to use the module to momentarily connect a separate 12VDC circuit. (Mimicking a make/break switch.)Already have many FGS211/FGS221 modules which are dry. But want to make sure there is no change of internal circuitry for this module. View answer

Asked 3 ´years ago | Z-Wave Fibaro Double Switch 2

Question 8

I was wondering if I could use the SIR321 to control an immersion heater in my hot water tank, using the thermostat cable under the jacket so that I can monitor the temperature in the tank ? View answer

Asked 4 ´years ago | Z-Wave Plus Secure Wall Switch

Question 9

Hi I am unable to get the Fibaro FGS-224 Double Smart Module to work with Samsung SmartThings Hub v3. I have managed to get it to pair with the v3 hub but only as a generic multifunction device. Only one channel works as a switch. Regards Johan View answer

Asked 4 ´years ago | Z-Wave Fibaro Double Smart Module

Question 10

Is the battery replaceable? View answer

Asked 4 ´years ago | Z-Wave Plus Heiman Smoke Sensor

Question 11

Which zwave dimmer modules will this work with? View answer

Asked 4 ´years ago | Vision Dimmer Bypass

Question 12

Can you please confirm which version of ZigBee this interface uses? Is it Hue ort SmartThings compatible? The photo doesn't show a ZigBee logo and suggests that it is 2.4GHz RF only control? View answer

Asked 4 ´years ago | Zigbee Controller For RGB And CCT LED Strip

Question 13

Manual says "Maximum length of wires: 3 meters". Is that really the case and does it apply for both input and output wiring? Thinking of installing these on the DIN rail with Eutonomy housings, but 3-meter cable restriction would make this impossible. View answer

Asked 4 ´years ago | Z-Wave Fibaro Double Smart Module

Question 14

Please could somebody advise me of the hole centre dimensions of the mounting bracket ? I need to fix the mounting bracket directly to an existing UK metal back box. Thank you.

Asked 4 ´years ago | Z-Wave Remotec Scene Master

Question 15

what is the size of the motion sensor? View answer

Asked 4 ´years ago | Zigbee Aeotec SmartThings Motion Sensor

Question 16

How is this different from the earlier version? View answer

Asked 4 ´years ago | Z-Wave Plus Heiman Smart Smoke Sensor 2

Question 17

Hi, is it possible to remove the logo from the front easily? View answer

Asked 4 ´years ago | Z-Wave Plus MCO Home Glass Touch Dimmer

Question 18

Hi, is this compatible with Futurehome smarthub? (Model: CUBE-1V1-EU) View answer

Asked 4 ´years ago | Z-Wave Plus Eurotronic Air Quality Sensor Z-Wave Plus (VOC Sensor)

Question 19

How do these behave after a power cut is restored? Can the behaviour be configured like hue bulbs, for example last state? Thanks.

Asked 4 ´years ago | Zigbee Aduro B22 Bulb - Tunable Colour

Question 20

Hi would this be compatable with a wired ring video doorbell to allow me to open a gate remotely View answer

Asked 4 ´years ago | Z-Wave Popp Electronic Door Opener Controlmodule

Question 21

what is the z-wave frequency, i assume it is 868mhz? View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec Range Extender 6 - UK Socket

Question 22

Hi, I have one of these (SCS317) and haven't had much success adding it in to my Homey network, other than a generic device. Any advice or tips on how to add this would be gratefully received. Thanks View answer

Asked 4 ´years ago | Z-Wave Plus Secure 7 Day Programmable Room Thermostat

Question 23

Hello, I have many facilities in different places {hundreds} and I want to manage the entry permits for different suppliers. I would be happy if you get back to me how can this be done? asaf cohen View answer

Asked 4 ´years ago | Poly-Control Extendable Security Cylinder for Danalock V3

Question 24

This says Pi4 compatible but in the supporting documentation it says "not without un-powered USB hub)". Some have said that this is the latest version of this Z-stick but according to the Aeotec site there is a later version called Aeotec Gen5+ which is compatible with a Pi4 without having to use a USB hub. Anyone able to clarify this please? View answers

Asked 4 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 25

I see you only have the EU version in stock. What is the difference to the UK version, is it just the plug? ie could I simply put a UK plug on an EU version or use an adapter? View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec Doorbell 6

Question 26

Would this work with a LightwaveRF Hub? View answer

Asked 4 ´years ago | Z-Wave Remotec Scene Master

Question 27

Is it support EU frequency (868.42)? View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 28

Does this 'smart cable' have a physical power switch, similar to the discontinued Swwidinter zwave cord switches, or is it remote control only.

Asked 4 ´years ago | Zigbee Frient Smart Cable 2

Question 29

What’s the rated inductive load in amps for this? Many thanks. View answer

Asked 4 ´years ago | Zigbee Frient Smart Cable 2

Question 30

Does this integrate into smasung smartthings like the fire detector? View answer

Asked 4 ´years ago | Zigbee Frient Intelligent Heat Alarm

Question 31

Do you have to have smartthings to go with this bridge or does the bridge connect directly to to my WiFi router ? Thank you View answer

Asked 4 ´years ago | Danalock Danabridge

Question 32

I plan to use these for patio and window drop-arm awnings. The awning company supply the following motors: - the awning uses a Somfy Orea WT 35/17 - the drop arms use a Somfy Orea WT 15/17 Can anyone advise whether these Fibaro Roller Shutter 3s are compatible and if there is anything in particularly that I need to be alert of in installing? View answer

Asked 4 ´years ago | Z-Wave Fibaro Roller Shutter 3

Question 33

I have several Qubino Mini Dimmer modules in my current set up - HomeSeer with Aeotec Z-Stick controller. Can I substitute one of these for the Qubino module? View answer

Asked 4 ´years ago | Vesternet Z-Wave Dimmer

Question 34

Hi, I was wondering if this would work with Economy 7 electricity, meaning does it have an internal battery to keep it on and connected to the network when economy 7 isn't active? I'm wondering if it is possible to make economy 7 storage heaters smarter. Thanks. View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 35

Hi. Would I be able to use this at the same time as a Razzberry board or do they both require the same part of the gpio header (Pi3)? View answer

Asked 4 ´years ago | Zigbee Popp ZB-Shield

Question 36

Is there a battery included, just so I know if i need to order a seperate one or not, Thanks. View answer

Asked 4 ´years ago | Zigbee Aeotec SmartThings Motion Sensor

Question 37

Hi, I'm assuming I'll be able to control the Zigbee Popp Smart Thermostat via my Homey Hub. Can you confirm please? Many thanks David View answer

Asked 4 ´years ago | Zigbee Popp Smart Thermostat

Question 38

Can these alarms link together, so if one senses smoke they all go off? View answer

Asked 4 ´years ago | Z-Wave Plus Heiman Smart Smoke Sensor 2

Question 39

Will the switch send instant status updates back to Vera? To answer the review where this wasn't working I ended up finding the solution here https://community.ezlo.com/t/heltun-he-tps04-and-vera-lite-experience/217229

Asked 4 ´years ago | Z-Wave Plus V2 Heltun Touch Panel Switch - Four Buttons - White

Question 40

Hi, can this camera send images/video to my PC using FTP or some other protocol? View answer

Asked 4 ´years ago | Aeotec SmartThings Cam 360

Question 41

What is the length of the new Q-Reader lead between the pulse module and the data logger. I have a long distance (approximately 22m) between the meter (located next to road) and the house and propose to connect the pulse module to the requisite cores of a CAT5e cable (already laid underground) and then connect the Q-Reader within the house where it can connect via z-wave to my hub. Is this proposal possible if the cable is not long enough? View answer

Asked 4 ´years ago | Z-Wave Data Logger for E-Meters

Question 42

Is this also compatible with the Raspberry Pi 400 running Home Assistant? Or is there a suitable alternative I should look at? View answers

Asked 4 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 43

Is this the latest (2019, green) version of this board, or the slightly earlier (2018, blue) version? Obviously the photo shows a blue one, but good to know for sure! View answer

Asked 4 ´years ago | Z-Wave.me RaZberry 2 PI GPIO Daughter Card - Gen5 - New

Question 44

They were £24.99 before now £34 I'd call that a big difference.

Asked 4 ´years ago | Zigbee Aeotec SmartThings Motion Sensor

Question 45

Why has the prices gone up so much for what is just a rebrand. View answer

Asked 4 ´years ago | Zigbee Aeotec SmartThings Motion Sensor

Question 46

Is it resistant to condensation/waterproof? What is the operating humidity range? View answer

Asked 4 ´years ago | Z-Wave Fibaro Multi Sensor

Question 47

Does it include an acceleration sensor (accelerometer or any kind of vibration sensor) for door knocker detection? View answer

Asked 4 ´years ago | Z-Wave Technisat Door/Window Sensor

Question 48

Would this work with an existing KwikSet deadbolt? Thanks. View answer

Asked 4 ´years ago | Z-Wave and Bluetooth Poly-Control Danalock V3

Question 49

Hello, I bought it a month ago. What estimated date will it there be stock? When will I receive it? View answer

Asked 4 ´years ago | Aeotec SmartThings Cam 360

Question 50

Can you confirm I would receive the newer version of the ZMNHOD1 module? With updated flash And S7 firmware. The older ones have H1S5P1 printed on the sticker after the model number ZMNHOD1, these cannot be updated to the S7 firmware. Thanks View answer

Asked 4 ´years ago | Z-Wave Qubino Flush Shutter DC

Browse by Topic

Tools