Brands - Qubino Q&A

Question 1

Can I connect the module N/L to 230V while Q and I1,2,3 are being used with a 24VDC device? View answers

Asked 7 ´years ago | Z-Wave Qubino Flush Relay x 1 Plus

Question 2

Is it possible to use these to control a 240v relay without chatter? We tried this by altering parameters 11,12 and 15 but were not successful. Any advice appreciated. View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 3

Is this Controller working with vera plus? View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Shutter Plus

Question 4

What connectors do I need to order to extend this cable? I can get them from Farnell or RS if I know what are used. I'm assuming that this is a 1-wire sensor as it has three wires, pwr, gnd and the 1-wire bus, and that means that it can be extended to quite a few metres and I need to pick up the outside temperature... View answers

Asked 8 ´years ago | Qubino Temperature Sensor

Question 5

Why do these show as requiring a fuse whereas other like the Fibaro do not show this as a requirement in the wiring diagrams? View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 6

I read the following in the manual: Rated output power 8A for single output channel,13A at max.(3,25A for R.G.B.W. single output channel is suggested) I'm planing to control two strips of LED with the RGBW-Dimmer. Using two of the four channels. How much power (current) can each of the two LED-strips have? (I'm using a 24V driver). Maybe 13A/2 = 6.5A per channel? View answer

Asked 8 ´years ago | Brands - Qubino > Z-Wave Qubino RGBW Dimmer Plus

Question 7

Can this be connected to two bell-push switches, to activate two lighting scenes? The lights would be powered by other zwave modules (dimmers), so these would purely be used to trigger the scenes. View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 8

Can this be used as four separate 36w 12v channels? I want to control four sets of 12v led lamps but am not sure if it can only be controlled as if it were colour, so I would have to choose, for instance, yellow, to have two sets on? View answer

Asked 8 ´years ago | Brands - Qubino > Z-Wave Qubino RGBW Dimmer Plus

Question 9

I am looking for a Z-Wave Plus LED controller that has DMX512 output. Does this device or do you know of any others that fit the bill please? View answer

Asked 8 ´years ago | Brands - Qubino > Z-Wave Qubino RGBW Dimmer Plus

Question 10

Does this have the possibility of manual override in case Z-wave is down? I don´t see a button View answer

Asked 8 ´years ago | Qubino 32A Contactor for Smart Meter

Question 11

It says "For use with Qubino Smart Energy Meter". Is the Smart Meter a requirement to use this contactor or can it be used without it? View answers

Asked 8 ´years ago | Qubino 32A Contactor for Smart Meter

Question 12

Does anyone know if this unit is stable with HomeSeer? I have a couple of the Fibaro Dual Relay units but their status reporting is flaky at best and I cannot rely on them. - Thanks! View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 13

Can this unit be controlled by other Z-wave controllers? Is the Smart Meter required for it to function?

Asked 8 ´years ago | Qubino 32A Contactor for Smart Meter

Question 14

Can this unit be controlled from other z-wave controllers? or is the smart meter required? View answer

Asked 8 ´years ago | Brands - Qubino > Z-Wave Qubino Smart Meter ZMNHTD1 Plus

Question 15

Multiple questions --> What is the difference between the bi-stable and the contactor switch ? I need to switch a load of ~ 4k W (electrical water heater) which uses a double switch (live+neutral), which one suits better ? Do u have any feedback from Vera users that have managed to add them in their network (smart meter, contactor, bi-stable) ? View answer

Asked 9 ´years ago | Brands - Qubino > Qubino 32A Bistable Switch for Smart Meter

Question 16

Can someone explain dry / volrage free contacts? Trying to decide which module to use for controlling some outside lights. View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 17

Is it working with HC2? I have some issues with it. View answers

Asked 9 ´years ago | Brands - Qubino > Z-Wave Qubino Smart Meter ZMNHTD1 Plus

Question 18

In the manual it says 'Electrical installation must be protected by directly associated over current protection fuse 4A, gG or Time lag T....'. How can I do this? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 19

is there a video demonstration on how to connect cables? official qubino videos does not show how to connect.. View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 20

Can I turn on/off my lights with the existing switches? or do I need to control with controller application or via external switch? View answer

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 21

I used these in the past with LED power supplies but unfortunately even though the static current was under 1 amp, after a while the power supply inrush current would weld the relay contacts closed. I put a thermistor in-line with the load to limit the inrush and Qubino said they were aware of this and working on a solution. Does anyone know if this problem has been fixed?

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 22

how do you wire this on a 2wire 2switch system do you connect the N with each of the wires going to the lights? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 23

I bought and installed this. However to get it to act like a momentary push button for my garage door I need to set some parameters. What's the best way to do that? I have a SmartThings hub. Thanks! View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 24

Is this a repeater like the 1D model? If not what double relay would you recommend what is a repeater? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 25

Can the Qubino door sensor be connected into this and does it show as a operate sensor in the Z-wave control panel (Vera in my case)? I'm weighting up all my options for controlling a gate and this seems perfect if it runs from 24v and can have the door sensor connected directly into it as well. Less items to need to wire up View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 26

How do you use this module? View answers

Asked 9 ´years ago | Qubino Temperature Sensor

Question 27

Does this control 2 loads separately? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 28

Can this relay report the energy usage of the load connected to it? View answer

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Brands - Qubino Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools