Z-Wave Q&A

Question 1

Has anyone figured out how to set the light and humidity thresholds? The manual gives parameter values, sizes and hex/decimal descriptions but setting them don't match and the default values don't match the ones in the manuals, they aren't even close. Trying to set values gives me "Failed to set user settings" in my Vera Edge. View answers

Asked 9 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 2

Can you fit this in the light fitting or does it have to be in the switch socket? I think it probably has to be in the switch but I want to be sure before I start drilling out space behind the switch box. Thanks! View answers

Asked 9 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 3

Which would work better with the Fibaro Dimmer 2? GU5.3 (MR16/12V) LED bulbs or GU10 (240V) LED bulbs? (I'm replacing MR16 halogen bulbs and trying to decide whether to convert to GU10 fittings). View answers

Asked 9 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 4

Will it work wit fibaro HC Lite? View answer

Asked 9 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 5

What is the range at which the gestures will work over? And are there any materials the Swipe will not work behind, e.g. glass?

Asked 9 ´years ago | Z-Wave Fibaro Swipe

Question 6

The Fibaro Double Switch 2 Gen5 will work with vera plus? View answers

Asked 9 ´years ago | Z-Wave Fibaro Double Switch 2

Question 7

As far as I know this model like previous models should have "Manager Power" option, but in your site usage it didn't mention it. it realy does not have this option?! View answer

Asked 9 ´years ago | Z-Wave Fibaro Double Switch 2

Question 8

Does this stick battery prevent it from forgetting the network routing? I bought the UZB and whenever i unplug it from the pc or just reboot the pc, all routing is reset and it starts all over again resulting many times in dead nodes.. Is this the correct behaviour? Dow the Aeon stick do the same? View answers

Asked 9 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 9

briefly switches on then off when I use the attached physical switch rocker. Have cabled as per diagram for a single switch S1 to switch COM leftmost live to switch Live mains live (old style red) to rightmost live mains neutral (old style black) to N bridged N and Q1. Device is picked up in smartthings though toggle on/off doesn't do anything ... only a brief switch on and off when using attached physical switch rocker. Any ideas? View answers

Asked 9 ´years ago | Z-Wave Fibaro Single Switch 2

Question 10

How many LED GU10 Spotlights can one use with ONE Fibaro Dimmer 2? And are there any recommended LED GU10 Spotlights? View answers

Asked 9 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 11

How does this differ from the fibaro relay module? They seem to do exactly the same job. View answers

Asked 9 ´years ago | Z-Wave Fibaro Single Switch 2

Question 12

Does this support lower voltage DC like the earlier versions did, or only mains? View answer

Asked 9 ´years ago | Z-Wave Fibaro Double Switch 2

Question 13

Is this new Gen5 fuse protected to 8A To use in sockets or do you still require to fit an upstream fuse spur at 8A? Does this report power monitoring? View answer

Asked 9 ´years ago | Z-Wave Fibaro Single Switch 2

Question 14

In the manual it says 'Electrical installation must be protected by directly associated over current protection fuse 4A, gG or Time lag T....'. How can I do this? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 15

is there a video demonstration on how to connect cables? official qubino videos does not show how to connect.. View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 16

When will support for the Button be available in Vera Home Control ? View answers

Asked 9 ´years ago | Z-Wave Fibaro Button

Question 17

Is this able to be used outside e.g as a door bell? View answer

Asked 9 ´years ago | Z-Wave Fibaro Button

Question 18

Is it possible to wire this to a momentary wall switch? I understand this will invalidate the warranty View answers

Asked 9 ´years ago | Z-Wave Fibaro Button

Question 19

when will you have more of these in stock? i have been waiting what seems forever to see a UK Version.. View answers

Asked 9 ´years ago | Z-Wave Plus Aeotec Smart Switch 6 - UK

Question 20

Looking at Fibaro's site, they mention this can be powered by connecting it to VDC source. My current smoke alarms (3 of them) appear to be powered by 240v mains wiring. How can I utilise this with these smoke sensors? View answers

Asked 9 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 21

How do these cope installed in metal back boxes in a brick wall? I was considering installing these in the ceiling with the light fitting, but with some of the wire configurations i have here, i will need to install deeper metallic back boxes and install behind the switches. View answer

Asked 9 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 22

Can you advise what size the switch is?, I couldn't see it in the document. Or do you have more photographs of it from various angles next to an existing zwave socket like the tkb? View answers

Asked 9 ´years ago | Z-Wave Plus Aeotec Smart Switch 6 - UK

Question 23

Hi is this forUK sockets? Does this unit also act as a repeater for the network View answer

Asked 9 ´years ago | Z-Wave Plus Aeotec Smart Switch 6 - UK

Question 24

Can you link sensors together so that if one goes off the others will also trigger? View answers

Asked 9 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 25

Hi, Will the device perform the same activities when powered by battery as it will when powered by usb? Thanks View answers

Asked 9 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 26

Can I turn on/off my lights with the existing switches? or do I need to control with controller application or via external switch? View answer

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 27

I used these in the past with LED power supplies but unfortunately even though the static current was under 1 amp, after a while the power supply inrush current would weld the relay contacts closed. I put a thermistor in-line with the load to limit the inrush and Qubino said they were aware of this and working on a solution. Does anyone know if this problem has been fixed?

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 28

Will this be usable as a on/off toggle for Fluorescent tube lights? View answer

Asked 9 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 29

Normally when I think about DIN rails, I think about the 2 pole fuse/breakers in my house consumer unit. Where do these fit in ? Do they go in the same unit, next to the breaker for say the lighting ring/circuit I want to control/dim? Or do you recommend they go into a different unit - away from the main breakers etc? View answer

Asked 9 ´years ago | Z-Wave Qubino Din Dimmer Gen5

Question 30

Does this work with Vera Plus? or has anyone tried it yet? View answers

Asked 9 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 31

Does this new Z-Wave Fibaro Motion Sensor Gen5 version work with the zipabox? or is it just vera edge having problems? View answers

Asked 9 ´years ago | Z-Wave Fibaro Multi Sensor

Question 32

I am looking for a din rail switch to replace a timer switch in a house in Spain which currently controls my external lights. Would this work with a SamsungSmarthings unit instead? View answers

Asked 9 ´years ago | Z-Wave Qubino Din Dimmer Gen5

Question 33

Please can you tell me the maximum load (W) the UK version of this switch can handle? View answers

Asked 9 ´years ago | Z-Wave Plus Aeotec Smart Switch 6 - Schuko

Question 34

Can this be used with Fibaro Smoke and Water sensons, with just a notebook and some tools without a Home Center ? View answers

Asked 9 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 35

is this a USA frequency or EU? View answer

Asked 9 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 36

how do you wire this on a 2wire 2switch system do you connect the N with each of the wires going to the lights? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 37

What is the Z-wave frequency for this device? View answers

Asked 9 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 38

does it work with a fibaro hc2? View answer

Asked 9 ´years ago | Z-Wave Popp Weather Station

Question 39

Has someone tested this device with a veraplus controller ? (Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5 PHI_PST02-1A)

Asked 9 ´years ago | Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5

Question 40

Can this be used as a secondary device with another remote? View answers

Asked 9 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 41

will this work with samsung smarthings? View answer

Asked 9 ´years ago | Z-Wave Philio Multisensor - Light / Temp / Door - Gen5

Question 42

I bought and installed this. However to get it to act like a momentary push button for my garage door I need to set some parameters. What's the best way to do that? I have a SmartThings hub. Thanks! View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 43

Will this allow me to set z-wave parameters on individual devices using my Mac? View answers

Asked 9 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 44

Hi, Has anyone used this with the Vera Plus and UI7 (1.7.1786). If so did all of the sensors show up and work as expected? Thanks. View answer

Asked 9 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 45

Is this a repeater like the 1D model? If not what double relay would you recommend what is a repeater? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 46

Does it work on Fibaro? View answer

Asked 9 ´years ago | Z-Wave Popp Weather Station

Question 47

link this to wifi if poss ? View answer

Asked 9 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 48

Can the Qubino door sensor be connected into this and does it show as a operate sensor in the Z-wave control panel (Vera in my case)? I'm weighting up all my options for controlling a gate and this seems perfect if it runs from 24v and can have the door sensor connected directly into it as well. Less items to need to wire up View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 49

How do you use this module? View answers

Asked 9 ´years ago | Qubino Temperature Sensor

Question 50

Does this control 2 loads separately? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Z-Wave Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools