Browse by Category
Z-Wave Q&A
Activity timeframe
-
Will this work with the latest Aeotec Nano Dimmer for which does not have a bypass available yet? I cannot beleive that the internals will be much difference between provisors - basically some additional resistance and capacitance added. Has anyone tied this and can report compatability? View answer
Asked 8 ´years ago | Z-Wave Fibaro Dimmer Bypass 2
Asked 8 ´years ago | Z-Wave Data Logger for E-Meters
What's the difference between this model (FIBEFGS-223) and the FIBEFGS-222? One is described as a switch and the other as a relay, but otherwise seem identical. Does it make any difference to what it can do? I want to use them behind existing light switches to control lighting circuits - does it make any difference which I use? Thanks! View answers
Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2
Does this have Low Battery Alert? View answers
Asked 8 ´years ago | Z-Wave Fibaro Flood Sensor
Does this work with Samsung SmartThings Hub? View answers
Asked 8 ´years ago | Z-Wave Fibaro Flood Sensor
Does this device work fully with HomeSeer? View answer
Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2
Would there be a minimum GU10 number of lights that would not need a Fibaro dimmer 2 ? I have a number of circuits with GU10 lights 6W X 9 in a kitchen and out in a hallway 2 way circuits of 2 each by 2 and a circuit of 4. Would I need a dimmer bypass then for all circuits. View answer
Asked 8 ´years ago | Z-Wave Fibaro Universal Dimmer 2
Hi - when wired this into a double switch and then included this with a Vera Plus controller there were 3 devices created - the master and 2x appliance modules. In Vera only using the master switch has an affect and it only controls one of the switches. How do I include this so that both switches are controlled? View answer
Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2
Is this compatible with Home Assistant?
Asked 8 ´years ago | Z-Wave Fibaro Button
does it detect carbon monoxide? View answers
Asked 8 ´years ago | Z-Wave Fibaro Smoke Sensor
QNAP, OpenHAB + Aeon Labs Z-Stick USB, possible? I'm guessing this is possible, there is a package for OpenHab that will install on QNAP, so if I stick this USB stick into the back of the QNAP box will I be good to go? View answer
Asked 8 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)
I want to use a Fibaro relay to swicth an immersion heater on and off. The load is switched using a double pole relay. Can I simply connect the Fibaro output across the relay energising contacts, or will you need a resistor in series to reduce the current? View answer
Asked 9 ´years ago | Z-Wave Fibaro Double Switch 2
Is this device suitable for switching 230V LED lights, or would it be better to use the double relay switch instead? Since it doesn't have dry contacts, I'm wondering if the LEDs may flicker while switched off (as is the case for the dimmer module). View answers
Asked 9 ´years ago | Z-Wave Fibaro Double Switch 2
Will this work outside as a motion detection? View answers
Asked 9 ´years ago | Z-Wave Fibaro Multi Sensor
I look at the instruction manual for the wiring diagrams. I have two wires coming from the wall and it has no wall switch. When I moved in, it had a cheap strip light with shaver socket and its own onboard switch. I have removed this old fitting. I am planning to install an LED strip light running off 12V. I wish to use the Fibaro Dimmer 2 with bypass 2. When I look at the wiring diagram for a 2 wire setup, it assumes I will have a Wall Switch. This makes the diagram useless to me. Can anybody help with an adjusted diagram please? View answer
Asked 9 ´years ago | Z-Wave Fibaro Universal Dimmer 2
