Question 1

you said: Popp Mains Adapter can be used to power up the Z-Wave Popp Smoke Detector with mains supply. It eliminates the need to insert batteries in your smoke detector. after we tried to install it without battery it doesn't work then we contacted aeotec support they said: The smoke detector only works with the battery inserted. The smoke detector standard stipulates this. The 12 V supply serves to support the lifetime of the device by supplying the Z-Wave circuit board with external voltage. This doubles the lifetime of the 9V battery. could you explain please? Ahmad View answer

Asked 7 ´years ago

Question 2

Will it work with Fibaro (Home Center 2)?

Asked 7 ´years ago

Question 3

What Bypass should be used in a 2-Wire installation? The manual says; "When installing the Mini Dimmer, with LED loads, in a 2-wired installation, if the load connected to the output starts flickering, we recommend you use a Bypass." I have installed it in to a 2-wire installation with an LED light and it is flickering. The Aeotech and Fibaro dimmers all say that only their own bypass modules are compatible, is this also the case with the Qubino dimmers? View answer

Asked 7 ´years ago

Question 4

Can you measure the energy through the contractor separately from the smart meter unit View answer

Asked 7 ´years ago

Question 5

How do you set this to simple on/off rather than dimming. I want to use it in the UK with 2 wire circuit, toggle on off switch connected to S1 and non dimmable CFL or LED bulbs View answer

Asked 7 ´years ago

Question 6

Hi does this support LED bulbs? View answer

Asked 7 ´years ago

Question 7

Does this come with a Zwave licence or is that an additional cost? View answers

Asked 7 ´years ago

Question 8

Will this device work fully with Hc2? Thanks View answer

Asked 7 ´years ago

Question 9

Hi Does this come with a UK standard 3 point plug? I'm trying to create a set up where I have a magnetic strip sensor on a door that will chime once opened and also send an alert to my phone. Do you know if this could be achieved, using this in conjunction with a smart things hub? Thanks View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Siren 6

Question 10

I assume that one button is included with the Doorbell? Can you please publish the dimensions of the bell (not given in the specification) and confirm that it can be battery powered. Thanks. View answers

Asked 7 ´years ago

Question 11

If the z-wave controller is temporarily offline will the chime still sound when the button is pressed, or is all functionality entirely dependent on the z-wave network?

Asked 7 ´years ago

Question 12

Can multiple thermostats be associated to this device? ie. Can mulitple devices call for heat via this switch ? View answer

Asked 7 ´years ago

Question 13

Does the siren/doorbell unit fit directly into a UK 3-pin socket or does it require a euro-adaptor?

Asked 7 ´years ago

Question 14

Can you install your own ringtones?

Asked 7 ´years ago

Question 15

Is the battery rechargeable or replaceable? View answers

Asked 7 ´years ago | Z-Wave Philio Multisensor - PIR / Light / Temp - Gen5

Question 16

I bought one of these earlier in the year, am hoping to use to add functionality to an automatic gate opener. I've struggled to get it added into Homeseer correctly, only Output 1 has shown up. Have any Homeseer users had any success getting both outputs to add correctly? If so, any tips? View answer

Asked 7 ´years ago

Question 17

Does this module work with wood venitian blinds? View answer

Asked 7 ´years ago

Question 18

Hi, Can you tell me if the Vision Dimmer Bypass should work with the Fibaro Dimmer 1 module? Thanks View answer

Asked 7 ´years ago

Question 19

Which z wave stick / hub / device do you recommend for use with Secure Thermostat / Receiver and Homeseer? Please note I am a long time user of Homeseer (early 2000) upgrading from HS1,2 to HS3. For the last 15 years I have used a purpose designed multi (6) zone system controlled by Homeseer running Xap plugin to Phaedrus NETIOM to create heating scenes. I am now moving on to an existing single zone combi boiler dwelling. I have no desire or requirement to rejig the new system to a plumbed multi-zone effort. I see this combination as a first step to migrate to a zwave set up from my X10 devices, curing the heating issue in the process. View answer

Asked 7 ´years ago

Question 20

Does this control both hot water and heating? View answers

Asked 7 ´years ago

Question 21

Why is there no technical documentation on your site for this device? The description and spec is very poor, as well.

Asked 7 ´years ago

Question 22

Why should i use this product? View answer

Asked 7 ´years ago

Question 23

Can you clarify what this means, in real terms, "Battery operated possible: 1x PT502035 (400mAh) (only for bridging)"? Can I use it as doorbell with just the batteries or does it have to be plugged in?

Asked 7 ´years ago

Question 24

Can these fit into one of the "Aeotec Recessor for MultiSensor 6" per chance, even if they are not designed too? View answer

Asked 7 ´years ago

Question 25

On what Mhz does it works and does it work on a HC2 from Fibaro View answer

Asked 7 ´years ago

Question 26

Can this be mounted outside? View answer

Asked 7 ´years ago

Question 27

Please advise the lead time for these modules. We need to procure 5 of them as soon as available. Regards, Warwick

Asked 7 ´years ago

Question 28

Hello Could I use this connected to the 12v bell output (I.e. the +and- terminals) in my house intruder alarm to tell my Samsung SmartThings box that the siren is ringing? This would be a remote alert as lightening frazzled the built-in comms dialler! It’s not clear to me from the manual that I could put the 12v through to say “it’s ringing” and “stopped ringing” when it’s 0v. I am also not clear on whether I will be able to configure it with ST (I don’t have the Fibaro control system), or not. Thank you in advance. Neil

Asked 7 ´years ago

Question 29

Is the usb power on permanently or does it switch on and off with the main unit? View answer

Asked 7 ´years ago

Question 30

I've tried to standardise with Fibaro kit but their Dimmer 2 doesn't appear to offer 0-10V output like this Qubino Flush Dimmer. Is that right? View answer

Asked 7 ´years ago

Question 31

Is this model come with a UK plug ?

Asked 7 ´years ago | Z-Wave Plus Aeotec Siren 6

Question 32

Hello, I was wondering whether you have this item suitable for an american-style box, at the size of 120mm wide, instead of 86mm? Thanks, Gal.

Asked 7 ´years ago

Question 33

Managed to put in a workaround but I found with a original style lightbulb it would cut out when I turn the brightness above 60% and then start flashing red. I've updated the config so that max power is 60% as this is just the porch light and I don't really need it that bright in there. But I'm concerned what happens if I purchase more.

Asked 7 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 34

I ordered this product before 3 days. Can you tell when the item will be in stock? Thank you.

Asked 7 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 35

I bought two of these to replace the previous generation ones. however, I'm unable to control these lights remotely on my Vera unit from other devices. Aeotec 4 button remote. I've seen other people who can't now remotely control these. Any ideas?

Asked 7 ´years ago

Question 36

I have a fibaro lite home center - with sensor strips on windows and doors. Is this compatible? View answer

Asked 7 ´years ago

Question 37

I have purchased this and it works fine, but I can't find a way to mount it nicely. UK backboxes and the extension plates for them have recessed mounting tabs. The switch can xxxx on to these with no problem, but it is recessed too far for the front cover to be able to clip onto the main switch housing. Please advise.

Asked 7 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 38

what kind of range should I expect for this? I have a lot of walls between where my vera is and where my 433 device is... View answer

Asked 7 ´years ago

Question 39

I will be building a new house starting in a few months time and I want to implant temperature sensors in the concrete slab. I have 2 questions; firstly in the manual it says this can be burried concrete with the right protection, what would that protection be please?? Secondly, what would you recommend for protecting the string of temp tensors so they can be safely buried in the concrete and what cable would you connect them with ?? Thanks Chris

Asked 7 ´years ago

Question 40

Hi, I'm using Domoticz running on a RPi, does this classify as a 'security Enabled Z-Wave Plus Controller' as specified as a requiremjent to fully utilise the Remotec ZXT-600 Z-Wave+ to IR Extender for AC ? Thanks Steve View answer

Asked 7 ´years ago

Question 41

Does this support pulse counting at hardware level ? I'm looking for something to interface to water flow meters with a pulsed output. It would obviously need to store number of pulses received over a certain time period.

Asked 7 ´years ago

Question 42

Will this work with Samsung Smartthings ? View answer

Asked 7 ´years ago

Question 43

Will the Z-Wave Qubino Flush Dimmer 0-10V Plus work with Samsung smartthings to control my Ecopac Constant Voltage 0/1-10V Dimmable LED Driver ELED-200-24V 200W 24V

Asked 7 ´years ago

Question 44

When will this product be in stock? View answer

Asked 7 ´years ago

Question 45

This appears to be a re-incarnation of the Fibaro Universal Binary Sensor which will not now recognise DS18B20 inputs although it used to do so. Is this unit any the more reliable?

Asked 7 ´years ago

Question 46

I wish to use this to wirelessly (zwave) control my Danfoss thermostats (also Zwave). Can you confirm that this devise is able to do so? And, I wonder if the fan-controller can be used to automatically turn on a fan for heat-moving near the fireplace? Say, if it is 23 degree it should automatically turn on the vent. But if it is too noisy or so, I can turn down the speed? Its hard to find the exact details on this product and MCO does not reply on their website... Thanks! View answer

Asked 7 ´years ago | Z-Wave Plus MCO Home Fan Coil Thermostat - 4 Pipe

Question 47

Hi, When will the Z-Wave Fibaro Double Switch 2 be available in stock? I have been waiting for the appearance of this device around a week( View answer

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 48

Hi. Can I use 3 x 7W led bulbs and 1 x 3W led bulb on the same circuit? Or do all the bulbs need to be the same wattage? Thanks View answer

Asked 7 ´years ago

Question 49

Good afternoon- can you confirm that this will only work with Popp ? and is NOT compatible with any Z-Wave hub devices ie Fibaro ? Best regards Chris

Asked 7 ´years ago

Question 50

Can this product be used outdoors? View answer

Asked 7 ´years ago

Browse by Topic

Tools