Question 1

How many LED GU10 Spotlights can one use with ONE Fibaro Dimmer 2? And are there any recommended LED GU10 Spotlights? View answers

Asked 10 ´years ago

Question 2

How does this differ from the fibaro relay module? They seem to do exactly the same job. View answers

Asked 10 ´years ago | Z-Wave Fibaro Single Switch 2

Question 3

Does this support lower voltage DC like the earlier versions did, or only mains? View answer

Asked 10 ´years ago | Z-Wave Fibaro Double Switch 2

Question 4

Is this new Gen5 fuse protected to 8A To use in sockets or do you still require to fit an upstream fuse spur at 8A? Does this report power monitoring? View answer

Asked 10 ´years ago | Z-Wave Fibaro Single Switch 2

Question 5

In the manual it says 'Electrical installation must be protected by directly associated over current protection fuse 4A, gG or Time lag T....'. How can I do this? View answers

Asked 10 ´years ago

Question 6

is there a video demonstration on how to connect cables? official qubino videos does not show how to connect.. View answers

Asked 10 ´years ago

Question 7

When will support for the Button be available in Vera Home Control ? View answers

Asked 10 ´years ago | Z-Wave Fibaro Button

Question 8

Is this able to be used outside e.g as a door bell? View answer

Asked 10 ´years ago | Z-Wave Fibaro Button

Question 9

Is it possible to wire this to a momentary wall switch? I understand this will invalidate the warranty View answers

Asked 10 ´years ago | Z-Wave Fibaro Button

Question 10

when will you have more of these in stock? i have been waiting what seems forever to see a UK Version.. View answers

Asked 10 ´years ago

Question 11

Looking at Fibaro's site, they mention this can be powered by connecting it to VDC source. My current smoke alarms (3 of them) appear to be powered by 240v mains wiring. How can I utilise this with these smoke sensors? View answers

Asked 10 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 12

How do these cope installed in metal back boxes in a brick wall? I was considering installing these in the ceiling with the light fitting, but with some of the wire configurations i have here, i will need to install deeper metallic back boxes and install behind the switches. View answer

Asked 10 ´years ago

Question 13

Can you advise what size the switch is?, I couldn't see it in the document. Or do you have more photographs of it from various angles next to an existing zwave socket like the tkb? View answers

Asked 10 ´years ago

Question 14

Hi is this forUK sockets? Does this unit also act as a repeater for the network View answer

Asked 10 ´years ago

Question 15

Can you link sensors together so that if one goes off the others will also trigger? View answers

Asked 10 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 16

Do you sell a similar night latch for outward opening doors? View answers

Asked 10 ´years ago

Question 17

Can this unit be used to trigger events in a controller (in my case the Homeseer Hometroller Zee S2) rather than being paired with a boiler receiver? I have two electric radiators in a room, and want to turn them on and off based on the thermostat reading. So I would create the various events to change the set point in the Homeseer, but also want the thermostat to trigger the events which turn the radiators on and off. Would that work, or should I be looking at something else? View answers

Asked 10 ´years ago

Question 18

Hi, Will the device perform the same activities when powered by battery as it will when powered by usb? Thanks View answers

Asked 10 ´years ago

Question 19

Hi all. I have a garden office heated by an electric oil filled radiator which I control with a ZWave socket. I use the temperature sensor in a movement sensor, and I link the two with a software thermostat on a Vera Lite. It works, but I'd prefer to have something where I can physically override the temperature and visually see what the current setting is. This unit looks ideal, but can it be made to switch my simple on/off ZWave socket? And can I set a schedule by simply getting my Vera to set the temperature according to my schedule, rather than using the unit's built in timer? Thanks in advance, Andrew. View answer

Asked 10 ´years ago

Question 20

Can I turn on/off my lights with the existing switches? or do I need to control with controller application or via external switch? View answer

Asked 10 ´years ago

Question 21

I used these in the past with LED power supplies but unfortunately even though the static current was under 1 amp, after a while the power supply inrush current would weld the relay contacts closed. I put a thermistor in-line with the load to limit the inrush and Qubino said they were aware of this and working on a solution. Does anyone know if this problem has been fixed?

Asked 10 ´years ago

Question 22

Will this be usable as a on/off toggle for Fluorescent tube lights? View answer

Asked 10 ´years ago

Question 23

Normally when I think about DIN rails, I think about the 2 pole fuse/breakers in my house consumer unit. Where do these fit in ? Do they go in the same unit, next to the breaker for say the lighting ring/circuit I want to control/dim? Or do you recommend they go into a different unit - away from the main breakers etc? View answer

Asked 10 ´years ago

Question 24

Does this work with Vera Plus? or has anyone tried it yet? View answers

Asked 10 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 25

Does this new Z-Wave Fibaro Motion Sensor Gen5 version work with the zipabox? or is it just vera edge having problems? View answers

Asked 10 ´years ago | Z-Wave Fibaro Multi Sensor

Question 26

Do you stock these in polished brass as well as the satin chrome? View answers

Asked 10 ´years ago

Question 27

Can you wire this between an LED strip and a 12v transformer? View answer

Asked 10 ´years ago

Question 28

I am looking for a din rail switch to replace a timer switch in a house in Spain which currently controls my external lights. Would this work with a SamsungSmarthings unit instead? View answers

Asked 10 ´years ago

Question 29

Please can you tell me the maximum load (W) the UK version of this switch can handle? View answers

Asked 10 ´years ago

Question 30

Can this be used with Fibaro Smoke and Water sensons, with just a notebook and some tools without a Home Center ? View answers

Asked 10 ´years ago

Question 31

is this a USA frequency or EU? View answer

Asked 10 ´years ago

Question 32

how do you wire this on a 2wire 2switch system do you connect the N with each of the wires going to the lights? View answers

Asked 10 ´years ago

Question 33

Is this tag compatible with Yale Doorman (Nordic market)? View answer

Asked 10 ´years ago

Question 34

What is the Z-wave frequency for this device? View answers

Asked 10 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 35

does it work with a fibaro hc2? View answer

Asked 10 ´years ago

Question 36

Has someone tested this device with a veraplus controller ? (Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5 PHI_PST02-1A)

Asked 10 ´years ago | Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5

Question 37

Can this be used as a secondary device with another remote? View answers

Asked 10 ´years ago

Question 38

Does it work with the z-way software?

Asked 10 ´years ago

Question 39

this is full compatible with vera3 ui5? View answer

Asked 10 ´years ago

Question 40

Does this conform to the Zensys Serial API? View answer

Asked 10 ´years ago

Question 41

Is the Everspring flood sensor a moving float or does it a water sensor? View answers

Asked 10 ´years ago

Question 42

will this work with samsung smarthings? View answer

Asked 10 ´years ago

Question 43

I bought and installed this. However to get it to act like a momentary push button for my garage door I need to set some parameters. What's the best way to do that? I have a SmartThings hub. Thanks! View answers

Asked 10 ´years ago

Question 44

Will this allow me to set z-wave parameters on individual devices using my Mac? View answers

Asked 10 ´years ago

Question 45

Is this compatible with OpenZwave / Domoticz on a Windows pc? View answer

Asked 10 ´years ago

Question 46

can the probe be cut to shorten it? or would that ruin the readings.? View answers

Asked 10 ´years ago

Question 47

Hi, Has anyone used this with the Vera Plus and UI7 (1.7.1786). If so did all of the sensors show up and work as expected? Thanks. View answer

Asked 10 ´years ago

Question 48

Is this a repeater like the 1D model? If not what double relay would you recommend what is a repeater? View answers

Asked 10 ´years ago

Question 49

Does it work on Fibaro? View answer

Asked 10 ´years ago

Question 50

link this to wifi if poss ? View answer

Asked 10 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Browse by Topic

Tools