Smart Home Sensors Q&A

Question 1

Looking at Fibaro's site, they mention this can be powered by connecting it to VDC source. My current smoke alarms (3 of them) appear to be powered by 240v mains wiring. How can I utilise this with these smoke sensors? View answers

Asked 9 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 2

Can you link sensors together so that if one goes off the others will also trigger? View answers

Asked 9 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 3

Hi, Will the device perform the same activities when powered by battery as it will when powered by usb? Thanks View answers

Asked 9 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 4

Can I turn on/off my lights with the existing switches? or do I need to control with controller application or via external switch? View answer

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 5

I used these in the past with LED power supplies but unfortunately even though the static current was under 1 amp, after a while the power supply inrush current would weld the relay contacts closed. I put a thermistor in-line with the load to limit the inrush and Qubino said they were aware of this and working on a solution. Does anyone know if this problem has been fixed?

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 6

Normally when I think about DIN rails, I think about the 2 pole fuse/breakers in my house consumer unit. Where do these fit in ? Do they go in the same unit, next to the breaker for say the lighting ring/circuit I want to control/dim? Or do you recommend they go into a different unit - away from the main breakers etc? View answer

Asked 9 ´years ago | Z-Wave Qubino Din Dimmer Gen5

Question 7

Does this work with Vera Plus? or has anyone tried it yet? View answers

Asked 9 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 8

Does this new Z-Wave Fibaro Motion Sensor Gen5 version work with the zipabox? or is it just vera edge having problems? View answers

Asked 9 ´years ago | Z-Wave Fibaro Multi Sensor

Question 9

I am looking for a din rail switch to replace a timer switch in a house in Spain which currently controls my external lights. Would this work with a SamsungSmarthings unit instead? View answers

Asked 9 ´years ago | Z-Wave Qubino Din Dimmer Gen5

Question 10

how do you wire this on a 2wire 2switch system do you connect the N with each of the wires going to the lights? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 11

What is the Z-wave frequency for this device? View answers

Asked 9 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 12

Has someone tested this device with a veraplus controller ? (Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5 PHI_PST02-1A)

Asked 10 ´years ago | Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5

Question 13

will this work with samsung smarthings? View answer

Asked 10 ´years ago | Z-Wave Philio Multisensor - Light / Temp / Door - Gen5

Question 14

I bought and installed this. However to get it to act like a momentary push button for my garage door I need to set some parameters. What's the best way to do that? I have a SmartThings hub. Thanks! View answers

Asked 10 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 15

Hi, Has anyone used this with the Vera Plus and UI7 (1.7.1786). If so did all of the sensors show up and work as expected? Thanks. View answer

Asked 10 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 16

Is this a repeater like the 1D model? If not what double relay would you recommend what is a repeater? View answers

Asked 10 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 17

Can the Qubino door sensor be connected into this and does it show as a operate sensor in the Z-wave control panel (Vera in my case)? I'm weighting up all my options for controlling a gate and this seems perfect if it runs from 24v and can have the door sensor connected directly into it as well. Less items to need to wire up View answers

Asked 10 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 18

Does this control 2 loads separately? View answers

Asked 10 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 19

Does this work with cats? Pet Friendly? View answer

Asked 10 ´years ago | Z-Wave Fibaro Multi Sensor

Question 20

I have one of these and a Samsung smart hub... hoping use various items from one place. The motion sensor is recognised as a door/window sensor? View answers

Asked 10 ´years ago | Z-Wave Fibaro Multi Sensor

Question 21

Can the earthquake mode be ran concurrently with motion detection? View answer

Asked 10 ´years ago | Z-Wave Fibaro Multi Sensor

Question 22

Whats new in this Gen 5 version? View answers

Asked 10 ´years ago | Z-Wave Fibaro Multi Sensor

Question 23

Does this work with both UI5 and UI7? View answers

Asked 10 ´years ago | Z-Wave Fibaro Multi Sensor

Question 24

Has anyone used the Aeon Labs Multisensor 6 - Gen5 on a VeraLite (UI5 1.5.622)? Did all sensors report correctly? View answer

Asked 10 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 25

Can this relay report the energy usage of the load connected to it? View answer

Asked 10 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 26

Is there a mains powered version of this smoke detector? View answers

Asked 10 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 27

Is this MultiSensor 6 in EU Frequency? View answers

Asked 10 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 28

Can the sensitivity be set so pets are ignored? View answers

Asked 10 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Smart Home Sensors Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools