In Push LV setup are the switch inputs dry contacts? View answer
Asked 2 ´years ago | Vesternet Z-Wave Switch
were do the grey and yellow wires get connected? View answer
Asked 2 ´years ago | Z-Wave Philio In Wall Switch
Zwave high load switch View answer
Asked 2 ´years ago | Vesternet Z-Wave High Load Switch
Where is correct driver for hubitat full capablities View answer
Asked 2 ´years ago | Z-Wave Philio In Wall Switch
Does this relay work without a neutral wire? View answer
Asked 2 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus
Asked 2 ´years ago | Z-Wave Fibaro Relay Insert 1 * 3 KW
Does this work with Home Assistant? View answer
Asked 2 ´years ago | Vesternet Z-Wave Switch
Philio PAN03 assiciation question View answer
Asked 2 ´years ago | Z-Wave Philio In Wall Switch
High load switch requires three wires? View answer
Asked 2 ´years ago | Vesternet Z-Wave High Load Switch
Can this be configured so that when the switch is off then power is still sent to the light bulb? I have a smart light bulb and I want to be able to use this switch to send the command to turn on and off the light and also be able to turn the smart light bulb on through an app even if the switch is off. View answer
Asked 3 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus
Hi, Regarding the Z-Wave Plus Aeotec Z-Stick 7, it shows âin stock soonâ, what does this mean, do you happen to have more info (eta) on this? Also, I presume when I buy this product the frequency band will be comply with EU (as I am living in Holland)? Thank you in advance! Kr, Daniel View answer
Asked 3 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch
Before buying this I wonder if anyone has tried the Smartthings Web driver reassignment as in this discussion:https://community.smartthings.com/t/fibaro-fgs-224-any-experience-dh/199429I see @johan has asked a similar question. I cannot find any published drivers for Smartthings other than this forcing the device assignment as double switch. View answer
Asked 3 ´years ago | Z-Wave Fibaro Double Smart Module
Before buying this I wonder if anyone has tried the Smartthings Web driver reassignment as in this discussion: https://community.smartthings.com/t/fibaro-fgs-224-any-experience-dh/199429 I see @johan has asked a similar question. I cannot find any published drivers for Smartthings other than this forcing the device assignment as double switch. View answer
Asked 3 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus
Are the contacts in this model 'dry'? I want to use the module to momentarily connect a separate 12VDC circuit. (Mimicking a make/break switch.)Already have many FGS211/FGS221 modules which are dry. But want to make sure there is no change of internal circuitry for this module. View answer
Asked 3 ´years ago | Z-Wave Fibaro Double Switch 2
Hi I am unable to get the Fibaro FGS-224 Double Smart Module to work with Samsung SmartThings Hub v3. I have managed to get it to pair with the v3 hub but only as a generic multifunction device. Only one channel works as a switch. Regards Johan View answer
Asked 3 ´years ago | Z-Wave Fibaro Double Smart Module
Manual says "Maximum length of wires: 3 meters". Is that really the case and does it apply for both input and output wiring? Thinking of installing these on the DIN rail with Eutonomy housings, but 3-meter cable restriction would make this impossible. View answer
Asked 4 ´years ago | Z-Wave Fibaro Double Smart Module
Hi, I was wondering if this would work with Economy 7 electricity, meaning does it have an internal battery to keep it on and connected to the network when economy 7 isn't active? I'm wondering if it is possible to make economy 7 storage heaters smarter. Thanks. View answer
Asked 4 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch
Does this work with Samsung Smarthings? View answer
Asked 4 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus
If I put the relay on momentary mode and press the momentary switch once (and release), the light that connect to relay output will stay at ON (toggle) till I press the momentry again, is that correct? If so, does it means that for 2 way implementation I just need 2 momentry switches connect in parallel to the same input at the qubino 2 relay and every press on one of the momentry switch will toggle the light to ON or OFF? I can't find such suggestion in you app notes guides. Thank you! View answer
Asked 5 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus
Hi, I've recently purchased one of these devices and installed it on my veraplus. Its created the 'Double Switch 2', Q1 Load, and Q2 Load. On the double switch device, its got the status: Failed at: Setting special association. The 2 load switches appear to work ok. Any ideas how to resolve? Thanks View answer
Asked 6 ´years ago | Z-Wave Fibaro Double Switch 2
Would this work locally "out of the box" without connecting to a central z-wave controller? I understand remote commands require a controller but would a hardwired momentary switch be able to turn on the load immediately after wiring as well? View answer
Asked 6 ´years ago | Z-Wave Fibaro Double Switch 2
Just read the English installation instructions for the Fibaro FGS 223. They state "The device is designed for installation in a wall switch box of depth not less than 600mm." I'm not sure you can get a back box of that depth in the UK. Does this mean we can't use the device in a standard UK box? View answer
Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2
Hi, I have box with 3 switches controlling 3 lights (one for each). Is it possible to install this module to control one light with S1 and the other 2 lights with S2? the idea is that the controller will open/close the 2 lights together while manually using the physical switches I will still have separate control. Thanks. View answers
Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2
