Z-Wave - Modules - Relays / Switches Q&A

Question 1

The manual suggests this unit must be installed behind an Air Break Switch. Is this confirmed? As far as I was aware, air break switches are only used in the distribution network?

Asked 7 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 2

Can this control a central heating pump or just resistive load? View answers

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 3

It can be used to turn on/off power for an entire apartment (of course without the hub) if currently I have a 32A common switch? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 4

Does it work with Samsung SmartThings Hub (F-HUB-UK-V2)? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 5

The description states that this requires a neutral wire, however the single output version of this module does not; so is that correct in the description? View answer

Asked 7 ´years ago | Z-Wave Plus AEOTEC Dual Nano przełącznik z pomiaru mocy

Question 6

I'm trying to use this switch to control load by both S1 and S2 (connected to separate switch), but it my case switch connected into S2 has no impact on the load. I had no problem with achieving the same effect with Everspring module AN179, but somehow it does not work with Fibaro. Have anyone has achieved such configuration (controlling load by both S1 & S2)? View answer

Asked 7 ´years ago | Z-Wave Fibaro Single Switch 2

Question 7

Hi I is it possible to use this module with a 2 way switch? If so how should I connect/configure it? Thanks View answer

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 8

Hi does this product support 2 way switch as well or only 2 single switches? View answer

Asked 7 ´years ago | Z-Wave Plus AEOTEC Dual Nano przełącznik z pomiaru mocy

Question 9

Does this function as a normally open switch or normally closed switch? Is this configurable?

Asked 7 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 10

I have a fused Switch controlling a fan and want to use this controller to operate the fan remotely as well as enabling the fused switch to continue controlling the fan at the wall, is there a wiring diagram showing how to achieve this? View answers

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Switch On/Off Controller

Question 11

I have a Homeseer setup and have bought the Fibrao FGS 223. I have managed to include it but want to change the default toggle to momentary switch as that's what I have elsewhere [legacy X10]. I tried Setting Parameter 20 to 0 in homseer z-wave node but it just says error and dosent change. Any help please View answer

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 12

Hi, I want to use this to control a security light which doesn't have a switch. But it needs S1 to be toggled 3 times for inclusion. Is there anyway to include without this e.g. button B? View answers

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 13

Does this require 3-wire installation system (neutral)? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Switch On/Off Controller with Power Metering

Question 14

Hi, I will be using one of these to control a 32 Amp load and want to log energy usage. Will this be possible with a Vera Edge? View answers

Asked 7 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 15

Is it possible to use these to control a 240v relay without chatter? We tried this by altering parameters 11,12 and 15 but were not successful. Any advice appreciated. View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 16

Hi all, I have installed a couple of these (fgs223) on a 2 way switch. One is an on off switch and the other is a dimmer. I've put the switches behind the on off switch. That bit works well but now the separate dimmer won't dim it only switches on and off. Any suggestions? View answers

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 17

Why do these show as requiring a fuse whereas other like the Fibaro do not show this as a requirement in the wiring diagrams? View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 18

Do you think this product would be ok to control a cooker? View answers

Asked 8 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 19

Can this be connected to two bell-push switches, to activate two lighting scenes? The lights would be powered by other zwave modules (dimmers), so these would purely be used to trigger the scenes. View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 20

Can this module be used behind a standard UK Socket and control/monitor it? View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 21

What's the difference between this model (FIBEFGS-223) and the FIBEFGS-222? One is described as a switch and the other as a relay, but otherwise seem identical. Does it make any difference to what it can do? I want to use them behind existing light switches to control lighting circuits - does it make any difference which I use? Thanks! View answers

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 22

Has anybody seen an issue where the Q outputs don't follow the S inputs? I have to toggle the state of the input switch a few times to get it to sync up. The input switch is the microswitch on my Heating Control Valve. View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 23

I am using a pir to switch this on which seems to work but it keeps showing as device not detected! I'm using Vera edge is there a parameter I need to change or is it not compatible thanks View answers

Asked 8 ´years ago | Z-Wave Fibaro Single Switch 2

Question 24

Does this device work fully with HomeSeer? View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 25

Does anyone know if this unit is stable with HomeSeer? I have a couple of the Fibaro Dual Relay units but their status reporting is flaky at best and I cannot rely on them. - Thanks! View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 26

Hi - when wired this into a double switch and then included this with a Vera Plus controller there were 3 devices created - the master and 2x appliance modules. In Vera only using the master switch has an affect and it only controls one of the switches. How do I include this so that both switches are controlled? View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 27

Does this work with 3 way switched circuits? Can't find a wiring diagram for even 2way switching in the manual. View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 28

How can this be set up for two-way circuits? i.e. two switches controlling one light. I can't see a wiring diagram to support this in the manual. View answers

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 29

I want to use a Fibaro relay to swicth an immersion heater on and off. The load is switched using a double pole relay. Can I simply connect the Fibaro output across the relay energising contacts, or will you need a resistor in series to reduce the current? View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 30

Can someone explain dry / volrage free contacts? Trying to decide which module to use for controlling some outside lights. View answers

Asked 8 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 31

Does this module need retractive switches too? I'm guessing yes and it needs 2. View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 32

Is this device suitable for switching 230V LED lights, or would it be better to use the double relay switch instead? Since it doesn't have dry contacts, I'm wondering if the LEDs may flicker while switched off (as is the case for the dimmer module). View answers

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 33

Will it work wit fibaro HC Lite? View answer

Asked 8 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 34

The Fibaro Double Switch 2 Gen5 will work with vera plus? View answers

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 35

As far as I know this model like previous models should have "Manager Power" option, but in your site usage it didn't mention it. it realy does not have this option?! View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 36

briefly switches on then off when I use the attached physical switch rocker. Have cabled as per diagram for a single switch S1 to switch COM leftmost live to switch Live mains live (old style red) to rightmost live mains neutral (old style black) to N bridged N and Q1. Device is picked up in smartthings though toggle on/off doesn't do anything ... only a brief switch on and off when using attached physical switch rocker. Any ideas? View answers

Asked 8 ´years ago | Z-Wave Fibaro Single Switch 2

Question 37

How does this differ from the fibaro relay module? They seem to do exactly the same job. View answers

Asked 9 ´years ago | Z-Wave Fibaro Single Switch 2

Question 38

Does this support lower voltage DC like the earlier versions did, or only mains? View answer

Asked 9 ´years ago | Z-Wave Fibaro Double Switch 2

Question 39

Is this new Gen5 fuse protected to 8A To use in sockets or do you still require to fit an upstream fuse spur at 8A? Does this report power monitoring? View answer

Asked 9 ´years ago | Z-Wave Fibaro Single Switch 2

Question 40

In the manual it says 'Electrical installation must be protected by directly associated over current protection fuse 4A, gG or Time lag T....'. How can I do this? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 41

is there a video demonstration on how to connect cables? official qubino videos does not show how to connect.. View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 42

Can I turn on/off my lights with the existing switches? or do I need to control with controller application or via external switch? View answer

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 43

I used these in the past with LED power supplies but unfortunately even though the static current was under 1 amp, after a while the power supply inrush current would weld the relay contacts closed. I put a thermistor in-line with the load to limit the inrush and Qubino said they were aware of this and working on a solution. Does anyone know if this problem has been fixed?

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 44

how do you wire this on a 2wire 2switch system do you connect the N with each of the wires going to the lights? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 45

I bought and installed this. However to get it to act like a momentary push button for my garage door I need to set some parameters. What's the best way to do that? I have a SmartThings hub. Thanks! View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 46

Is this a repeater like the 1D model? If not what double relay would you recommend what is a repeater? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 47

link this to wifi if poss ? View answer

Asked 9 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 48

Can the Qubino door sensor be connected into this and does it show as a operate sensor in the Z-wave control panel (Vera in my case)? I'm weighting up all my options for controlling a gate and this seems perfect if it runs from 24v and can have the door sensor connected directly into it as well. Less items to need to wire up View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 49

Does this control 2 loads separately? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 50

Will this unit work with a Fibaro Home Centre 2? View answer

Asked 9 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Z-Wave - Modules - Relays / Switches Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools