SmartThings Compatible Q&A

Question 1

Hi, Will this work with Samsung SmartThings, controlling the duo switch independently. If not, can you advise what switches will? Thanks View answer

Asked 4 ´years ago | Z-Wave Plus V2 Heltun Touch Panel Switch - Two Buttons - White

Question 2

Is this compatible and will reliably work with Vera Secure? View answer

Asked 4 ´years ago | SmartThings Compatible > Z-Wave Plus Popp Flow Stop 2

Question 3

Hi, Will this switch work with gateway such as Vera and Homey? And when do you plan to have it in stock. Thanks! View answer

Asked 4 ´years ago | Z-Wave Plus V2 Heltun Touch Panel Switch - Five Buttons - White

Question 4

Is the relay single pole or double pole (ie does it switch only the live connection or both L and N connections)? View answer

Asked 4 ´years ago | Z-Wave Heatit Z-Relay - 25A

Question 5

There is no mention about power supply in the spec or how to use. I assume its batteries? Standard 2032s? View answers

Asked 4 ´years ago | SmartThings Compatible > Z-Wave Plus Popp Flow Stop 2

Question 6

I have several of these devices and wish to use them with Home Assistant. I have managed to lose the little document that came with them. Can you tell me what values I should use to know when the sensor has detected smoke, please? Many thanks, John Chapman View answer

Asked 4 ´years ago | Z-Wave Plus Heiman Smoke Sensor

Question 7

Hi do you know if these support Triac dimmable as required by these downlights ? https://www.electrical2go.co.uk/jcc-v50-colour-selectable-fixed-fire-rated-led-downlight-7w-650lm-ip65-white.html Thanks Rob View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 8

Dear Sir i want ask you about the switch in wich frequency do u have it . and do have it in stock . Thanks View answer

Asked 4 ´years ago | Z-Wave Plus V2 Heltun Touch Panel Switch - Five Buttons - White

Question 9

Could I use this module to control 300w towel radiator View answer

Asked 4 ´years ago | Z-Wave Qubino Flush Relay x 1 Plus

Question 10

Is this just a repeater or does it actually boost signal higher and receive with greater sensitivity than other repeaters such as built into the Aeotec Z-Wave Plus Aeotec Smart Switch 6? View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec Range Extender 6 - UK Socket

Question 11

has anyone tested it with Fibaro Home Center 2? Does it work ok? View answer

Asked 4 ´years ago | Z-Wave Qubino Flush Shutter Plus

Question 12

Would this be able to control non dimmable LEDs? View answer

Asked 4 ´years ago | Z-Wave Plus AEOTEC Dual Nano przełącznik z pomiaru mocy

Question 13

Hi, how well does this work with SmartThings and in particular the energy monitoring? Many thanks Mark View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec smart boost timer switch

Question 14

How well does this device work in Smartthings and in particular will Smartthings report power usage? Many thanks View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec smart boost timer switch

Question 15

How well do these sensative drip sensors work in carpetted areas. I have 2 areas of my house where we have experienced leaks and both have carpet. If these are not suitable can you recommend a z-wave sensor that might work? View answer

Asked 4 ´years ago | Z-Wave Sensative Drip - Gen5

Question 16

Please can you provide a guide to use the aeotec nano shutter to motorise Venetian blinds for tilt, raise and lower? View answer

Asked 4 ´years ago | Z-Wave Plus Aeotec Nano Shutter

Question 17

If I put the relay on momentary mode and press the momentary switch once (and release), the light that connect to relay output will stay at ON (toggle) till I press the momentry again, is that correct? If so, does it means that for 2 way implementation I just need 2 momentry switches connect in parallel to the same input at the qubino 2 relay and every press on one of the momentry switch will toggle the light to ON or OFF? I can't find such suggestion in you app notes guides. Thank you! View answer

Asked 4 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 18

Why does the Aeotec Multi 6 report a 23 lux when my Philips Hue sensor reports 14606 lux in virtually the same position. I've tried it with 3 Aeotec Multi 6s now with the same sort of difference, I'm concerned because I want to use to switch on lighting when required? They even report 0 lux when there is enough light to read a book! View answers

Asked 5 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 19

Will this sensor detect leaking natural gas. Ie if you knock the gas ring on the cooker and don’t light it View answer

Asked 5 ´years ago | Z-Wave Plus Heiman Gas Sensor

Question 20

Hi, Does this work with Yale Doorman that we have in Sweden? Best regards View answer

Asked 5 ´years ago | Yale Smart Living Z-Wave Module 2

Question 21

Could the solar outdoor siren be used in conjunction with Ring Smart alarm system, which is supposedly Z-Wave compatible? View answer

Asked 5 ´years ago | Z-Wave Popp Solar Outdoor Siren 2

Question 22

Will this work with SmartThings to trigger scenes? View answer

Asked 5 ´years ago | Z-Wave Plus MCO Touch Panel Switch - Four Load - UK

Question 23

How does this get physically installed? Does it need a backbox/ pattress box? View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec smart boost timer switch

Question 24

Is this work with Samsung Smartthing V3 hub? Can I control the switch using google assistant via Samsung Smartthing Hub v3?

Asked 5 ´years ago | Z-Wave Plus MCO Touch Panel Switch - Four Load - UK

Question 25

Is this compatible with Vera Plus?

Asked 5 ´years ago | Z-Wave Plus Aeotec Doorbell 6

Question 26

Hi does anyone know if this device is supported on the Fibaro Home Centre and if so what does the control panel look like? View answer

Asked 5 ´years ago | Z-Wave Qubino RGBW Dimmer Plus

Question 27

Is Z-Wave Plus Aeotec Smart Boost Timer Switch compatible with Piper. Regards, Ruairi

Asked 5 ´years ago | Z-Wave Plus Aeotec smart boost timer switch

Question 28

What Bypass should be used in a 2-Wire installation? The manual says; "When installing the Mini Dimmer, with LED loads, in a 2-wired installation, if the load connected to the output starts flickering, we recommend you use a Bypass." I have installed it in to a 2-wire installation with an LED light and it is flickering. The Aeotech and Fibaro dimmers all say that only their own bypass modules are compatible, is this also the case with the Qubino dimmers? View answer

Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer

Question 29

How do you set this to simple on/off rather than dimming. I want to use it in the UK with 2 wire circuit, toggle on off switch connected to S1 and non dimmable CFL or LED bulbs View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 30

Hi does this support LED bulbs? View answer

Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer

Question 31

Will this device work fully with Hc2? Thanks View answer

Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer

Question 32

If the z-wave controller is temporarily offline will the chime still sound when the button is pressed, or is all functionality entirely dependent on the z-wave network?

Asked 5 ´years ago | Z-Wave Plus Aeotec Doorbell 6

Question 33

Does the siren/doorbell unit fit directly into a UK 3-pin socket or does it require a euro-adaptor?

Asked 5 ´years ago | Z-Wave Plus Aeotec Doorbell 6

Question 34

Can you install your own ringtones?

Asked 5 ´years ago | Z-Wave Plus Aeotec Doorbell 6

Question 35

Why is there no technical documentation on your site for this device? The description and spec is very poor, as well.

Asked 5 ´years ago | Z-Wave Plus Aeotec smart boost timer switch

Question 36

Can you clarify what this means, in real terms, "Battery operated possible: 1x PT502035 (400mAh) (only for bridging)"? Can I use it as doorbell with just the batteries or does it have to be plugged in?

Asked 5 ´years ago | Z-Wave Plus Aeotec Doorbell 6

Question 37

Can these fit into one of the "Aeotec Recessor for MultiSensor 6" per chance, even if they are not designed too? View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec Doorbell 6

Question 38

On what Mhz does it works and does it work on a HC2 from Fibaro View answer

Asked 5 ´years ago | Yale Smart Living Z-Wave Module 2

Question 39

Can this be mounted outside? View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 40

Hello, I was wondering whether you have this item suitable for an american-style box, at the size of 120mm wide, instead of 86mm? Thanks, Gal.

Asked 5 ´years ago | SmartThings Compatible > Z-Wave Plus MCO Touch Panel Switch - Two Load - UK

Question 41

I have a fibaro lite home center - with sensor strips on windows and doors. Is this compatible? View answer

Asked 5 ´years ago | Z-Wave Popp Solar Outdoor Siren 2

Question 42

I wish to use this to wirelessly (zwave) control my Danfoss thermostats (also Zwave). Can you confirm that this devise is able to do so? And, I wonder if the fan-controller can be used to automatically turn on a fan for heat-moving near the fireplace? Say, if it is 23 degree it should automatically turn on the vent. But if it is too noisy or so, I can turn down the speed? Its hard to find the exact details on this product and MCO does not reply on their website... Thanks! View answer

Asked 6 ´years ago | Z-Wave Plus MCO Home Fan Coil Thermostat - 4 Pipe

Question 43

Hi, To control the lights via z-wave do I have to keep this switch always "on"? Or i can control via z-wave regardless of the status of the touch pannel? Thanks, Z View answer

Asked 6 ´years ago | Z-Wave Plus MCO Touch Panel Switch - Four Load - UK

Question 44

So I have this bulb now, it's connected to my vera plus, I can get it to dim and switch on/off. How to i change the color with in vera. Thanks

Asked 6 ´years ago | Z-Wave Plus Aeotec LED Bulb 6 Multi-White (E27)

Question 45

Can the temperature sensitivity be increased using parameters to change the bit length of the temperature sensor?

Asked 6 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 46

Does this switch supports dimmable LED lights? View answer

Asked 6 ´years ago | Z-Wave Plus MCO Touch Panel Switch - Four Load - UK

Question 47

Can I connect the module N/L to 230V while Q and I1,2,3 are being used with a 24VDC device? View answers

Asked 6 ´years ago | Z-Wave Qubino Flush Relay x 1 Plus

Question 48

Dear all, Is this model support for Z-Wave directly? Or we should buy one more Z-wave module? Thank you. C??ng. View answer

Asked 6 ´years ago | Yale Keyless Connected Smart Lock - Connected Ready - No Module

Question 49

Hi, looking for some information on these with Smartthings Hub. Does it create a z-wave switch for each button, or do you have to try create virtual switches? Thanks,

Asked 6 ´years ago | Z-Wave Plus MCO Touch Panel Switch - Four Load - UK

Question 50

Why do you list this as compatible with Anthony Homey? Like many so called compatible brands, Homey relies on 3rd party or community developers to write drivers (they call them Apps), and the various developers haven't added compatibility for this or original Yale Connected Keyfree), despite requests. Now that the lock is discontinued, I doubt it ever will be. View answers

Asked 6 ´years ago | Yale Smart Living Z-Wave Module 2

SmartThings Compatible Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools