SmartThings Compatible Q&A

Question 1

What is the average battery life in this button, how often does it need to be replaced or recharged? View answer

Asked 8 ´years ago | Z-Wave Philio Smart Colour Button Gen5

Question 2

Will this sensor work with an Aeotec Z-Stick V2 (Version: 1.4-2228-gbce4a88-dirty)?

Asked 8 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 3

Is it compatible with Nanoleaf smart light bulbs? View answer

Asked 8 ´years ago | Z-Wave Philio Smart Colour Button Gen5

Question 4

Can this use 2 x momentary switches? Can't see a way to configure them in the guide. View answer

Asked 8 ´years ago | Z-Wave Philio 2 * 1.5 KW Power Meter Plus

Question 5

Can someone explain dry / volrage free contacts? Trying to decide which module to use for controlling some outside lights. View answers

Asked 8 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 6

Has anyone figured out how to set the light and humidity thresholds? The manual gives parameter values, sizes and hex/decimal descriptions but setting them don't match and the default values don't match the ones in the manuals, they aren't even close. Trying to set values gives me "Failed to set user settings" in my Vera Edge. View answers

Asked 8 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 7

In the manual it says 'Electrical installation must be protected by directly associated over current protection fuse 4A, gG or Time lag T....'. How can I do this? View answers

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 8

is there a video demonstration on how to connect cables? official qubino videos does not show how to connect.. View answers

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 9

Hi, Will the device perform the same activities when powered by battery as it will when powered by usb? Thanks View answers

Asked 8 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 10

Can I turn on/off my lights with the existing switches? or do I need to control with controller application or via external switch? View answer

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 11

I used these in the past with LED power supplies but unfortunately even though the static current was under 1 amp, after a while the power supply inrush current would weld the relay contacts closed. I put a thermistor in-line with the load to limit the inrush and Qubino said they were aware of this and working on a solution. Does anyone know if this problem has been fixed?

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 12

how do you wire this on a 2wire 2switch system do you connect the N with each of the wires going to the lights? View answers

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 13

I bought and installed this. However to get it to act like a momentary push button for my garage door I need to set some parameters. What's the best way to do that? I have a SmartThings hub. Thanks! View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 14

Hi, Has anyone used this with the Vera Plus and UI7 (1.7.1786). If so did all of the sensors show up and work as expected? Thanks. View answer

Asked 9 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 15

Is this a repeater like the 1D model? If not what double relay would you recommend what is a repeater? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 16

Can the Qubino door sensor be connected into this and does it show as a operate sensor in the Z-wave control panel (Vera in my case)? I'm weighting up all my options for controlling a gate and this seems perfect if it runs from 24v and can have the door sensor connected directly into it as well. Less items to need to wire up View answers

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 17

Does this control 2 loads separately? View answers

Asked 9 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 18

Will this work with Smartthings? View answer

Asked 9 ´years ago | Z-Wave Philio Smart Colour Button Gen5

Question 19

Has anyone used the Aeon Labs Multisensor 6 - Gen5 on a VeraLite (UI5 1.5.622)? Did all sensors report correctly? View answer

Asked 9 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 20

Can this relay report the energy usage of the load connected to it? View answer

Asked 9 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 21

I have blinds that need to open in a certain order, can i use this switch as a start to a rule within indigo? Then press it twice to start another rule? View answer

Asked 9 ´years ago | Z-Wave Philio Smart Colour Button Gen5

Question 22

Hi. Is it compatible with Fibaro HC2? View answer

Asked 9 ´years ago | Z-Wave Philio Smart Colour Button Gen5

Question 23

Is this MultiSensor 6 in EU Frequency? View answers

Asked 9 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 24

Can the sensitivity be set so pets are ignored? View answers

Asked 9 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

SmartThings Compatible Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools